Search results

2013 JKUR, I have 20k miles on it so obviously it sits a lot in the garage, not sure if that matters. It sits on a trickle normally but I did forget to hook it up this time around and had to jump it to get it started. The issue is when I hit the gas, if I am in park or drive, the ABS light...

I have the evo long arm kit (the high clearance for the evo lever one) and am wondering if it would fit with the poison spyder frame mounted rocker knockers? Anyone have any idea?

Is the difference just that the low angle step comes out away from the jeep body more to create a more step up inside the jeep? I am trying to find the one that would provide for more clearance but can't seem to find an answer that explains the difference between the two..

Any one else have the same issue or know how to fix it? It appears they are sent sideways in an email from my iPhone.. and then load sideways here. Not sure what I am doing because they are not taken long ways on the phone and no rhyme or reason as to why some are sideways and some are right...

Trying to figure out how to remove the antenna from the fender.. currently on XRC fender armor but don't think that really matters, trying to go back t factory fenders so will need to uninstall here and then reinstall. Cant see to get this off though.. ideas? When the nuts move so does the bolt...

Selling Smittybilt XRC armor Front fender Rear Fender Body cladding Rock sliders 4 door JK In colorado only please. $700 takes everything or may be willing to split up..

Looking for an AEV heat reduction hood. Prefer black but open to colors.. I am located in CO and often visit AZ so either of those areas work unless willing to ship it.

ARB twin compressor arrives tomorrow with the Northridge4x4 mount it came with in the kit I bought.. but the more I read.. the more I think I might need the MORE mount. Who is running what mount and what are their thoughts? Anyone running a certain mount with the SPOD source next to it? My...

So occasionally when I am driving this light will pop up.. and then it will go away randomly as well. No rhyme or reason. Research points to being some ABS or speed sensor issue? Thoughts? How would I go about identifying the issue and correcting it is my real question.. Much appreciated!

Rugged Radios Basically brand new, mint condition, 4 headsets and intercom hook up. Used these twice in my Jeep for driving without doors and it was amazing how clear you could hear the music and your passengers. Great for any off road vehicle, buggy, sandrail, rock crawler, etc. Mainly used for...

Removing my Smittybilt XRC rock sliders and having issues remove the rear bolt. The front two came off no problem (16mm) and I jacked up the jeep so the long arm wasn't in the way of the forward rear bolt.. but the most rear bolt will not come off. It keeps slipping and I don't want to strip...

Currently have Smittybilt XRC front fender, rear fender, body cladding, and their rock sliders. I am going to swap to Poison Spyder's crusher flare and stock fender up front, their brawler rockers, and their crusher corner and crusher flare in the rear.. I am curious about the nutserts already...

So Im running the sPOD and bought a new 10" LED rigid industries light bar. The wiring rigid comes with has a fuse built/relay built into the power wire.. my question is do I need that fuse or can i just cut it out and wire the rest of the wire to the spod.. I feel like because the spod has...

Currently have a 2 gallon tank and compressor mounted in my trunk and trying to make some room and wondering if the extra tank is really worth it.. my understanding is that it just is nice to fill up while still driving so when you stop at end of trail it'll be faster to fill up that first tire...

So my VKSV3 bumper does not provide for much winch room.. below is a picture of the older version of a Smittybilt X2O 10k winch (22.3 inch x 5.4 inch x 9.4in). I am looking at getting the Warn Zeon 10-S winch (24.25 in. x 7.15 in. x 10.52in) and putting it in the same spot but I am not sure if...

In search of pictures/ideas to mount the winch control box in the engine bay.. mine doesn't fit in my front bumper (X2O 10k smittybilt winch) and trying to figure out where I should put it in my engine bay.. I have the SPOD and vacuum pump relocated driver side along the fender so not too much...

Post up pictures if you have either! Your .02 would be appreciated as well.. looking into grabbing one or the other and can't decide. I like the solid part of GenRight so don't have to worry about snagging on anything. Looking for something tucked up as possible..

Kind of late at this point but would like to create a build thread for my jeep! Wishlist: -Dynatrac PR60 front axle w/ RCVs -Dynatrac PR80 rear axle w/ chromoly shafts -Dynomax Quiet Crawler exhaust -Dual battery set up (undecided brand) -AEV heat reduction hood -42" tires (undecided, prob...

Hey all! I am in Colorado and got tired of paying shops to install parts and want to understand how everything works so I figure it is time to join a forum, so here I am. My current project is wiring up a winch control box off a X2O Smittybilt 10k winch. My plan is to mount it somewhere in...

I found a right hand drive jeep that was used for the postal service and it is in fairly good condition and runs - other than 170k miles. Anyone have any idea if I would run into issues modding it being RHD and not the normal LHD? I assume all the kits and what not would not fit without custom...