Cut Fender Thread

I have been wanting to chop my fenders for a while now. I just couldn't bring myself to start cutting away at my fenders....until this weekend. Left them on the jeep while I chopped em. I am very happy with the outcome gives my jeep a much better look! ImageUploadedByWAYALIFE1407163769.106748.jpgImageUploadedByWAYALIFE1407163784.334033.jpg


Sent from Junior's Iphone using WAYALIFE mobile app
 
I am still on the fence about chopping my stock fenders. My only worry is that they just get to floppy in the wind. Any thought?

I left some curve to the front that helps to push them down at highway speed but also used some 25 pound 3M double sides tape to stick them to the subframe at a couple of spots and no flapping at all. Figure this way they'll still give when I hit the inevitable rock.

ImageUploadedByWAYALIFE1407180787.347622.jpg
 
Finally cut my fenders today after debating for almost 2 years. Never was sure about cutting my painted fenders but after looking through this post and comparing the cost plus the chance of ripping one off. I bit the bullet and done it. I just wish I wouldn't have waited so long. I love the look!!!ImageUploadedByWAYALIFE1409016837.057630.jpgImageUploadedByWAYALIFE1409016848.405727.jpgImageUploadedByWAYALIFE1409016862.789744.jpgImageUploadedByWAYALIFE1409016875.267876.jpgImageUploadedByWAYALIFE1409016910.134559.jpg
 

Attachments

  • ImageUploadedByWAYALIFE1409016802.523057.jpg
    ImageUploadedByWAYALIFE1409016802.523057.jpg
    86.6 KB · Views: 695
Looks Awesome Mopar, great job and your right having Eddie's write up as a guide makes it a lot easier. :rock:
 
Im wondering if anyone has chopped their fenders like this? And if so have you noticed any problems with it. I like having the marker and it seems like a decent way to keep it if theres no problems.
And id definitely cut the rears like wayalife cuz they look good! And you'd think chrysler would just make em like this by now! :p

Just a note I did find this pic on google

Sent from my SGH-I337M using WAYALIFE mobile app

I've done mine similar to this as I have a full width bumper up front. Took out the chunky side marker and ran a smaller LED one instead though.

front chop.jpg
 

Attachments

  • new steps.jpg
    new steps.jpg
    131.5 KB · Views: 674
Last edited:
Finally cut my fenders today after debating for almost 2 years. Never was sure about cutting my painted fenders but after looking through this post and comparing the cost plus the chance of ripping one off. I bit the bullet and done it. I just wish I wouldn't have waited so long. I love the look!!!

Looks Awesome!! I'm still not brave enough to chop up mine lol, maybe one day I will, we shall see!
 
I'll join! Mine have been cut since last year when I got the 37's. Cut on the jeep and used the door edge trim. Someone couldn't believe they were just cut stockers.
 

Attachments

  • 1409068570693.jpg
    1409068570693.jpg
    63.7 KB · Views: 693
  • 1409068595052.jpg
    1409068595052.jpg
    96.9 KB · Views: 697
  • 1409068609382.jpg
    1409068609382.jpg
    154.1 KB · Views: 693
Got bored, re cut my fronts. Also took off all the door trim and cleaned up the edges. Including a balcony shot..
 

Attachments

  • 1409070788589.jpg
    1409070788589.jpg
    71.6 KB · Views: 686
  • 1409070803179.jpg
    1409070803179.jpg
    68.7 KB · Views: 693
  • 1409070821380.jpg
    1409070821380.jpg
    70 KB · Views: 678
  • 1409070857144.jpg
    1409070857144.jpg
    64.3 KB · Views: 693
What tool(s) is everyone using to cut the fenders for such smooth cuts.

Sent from my SPH-L710 using WAYALIFE mobile app
 
What tool(s) is everyone using to cut the fenders for such smooth cuts.

Sent from my SPH-L710 using WAYALIFE mobile app

i used a jig saw with a fine tooth blade, then hit it with this dry wall rasp tool i have. i actually used a utility knife this morning to cut the fronts, just scored it with a straight edge and kept going over it.
 
i used a jig saw with a fine tooth blade, then hit it with this dry wall rasp tool i have. i actually used a utility knife this morning to cut the fronts, just scored it with a straight edge and kept going over it.

And that got all the way through the fine see eventually? With a clean cut? That's good to know!
 
And that got all the way through the fine see eventually? With a clean cut? That's good to know!

Just take your time and measure. That rasp tool works great and if you use a utility knife, be sure to have a fresh blade. Here are some close ups. About as straight as I can get it. And I wouldn't try a utility knife on anything but straight cuts.
 

Attachments

  • 1409082371917.jpg
    1409082371917.jpg
    64.1 KB · Views: 664
  • 1409082384407.jpg
    1409082384407.jpg
    55.2 KB · Views: 644
  • 1409082395640.jpg
    1409082395640.jpg
    69.3 KB · Views: 663
  • 1409082406047.jpg
    1409082406047.jpg
    47.7 KB · Views: 669
Last edited:
What tool(s) is everyone using to cut the fenders for such smooth cuts.

Sent from my SPH-L710 using WAYALIFE mobile app

I ended up using a 3" cutoff wheel and took my time. I tried using a pneumatic saw, but it was taking WAY too long for me. I hit the very minor imperfections with a sanding block after.

Also a good thing to do is use a fabric tape measure (I made my own) and take a ton of measurements to duplicate a mirror image on both sides. I have pics of all that I just mentioned in my build thread. :yup:
 
Top Bottom