What was done to your rig this week?

[dillard09]

No...but I should have! I ended up using an Air wrench on the driver side and a regular wrench on the passenger side. Both sides however required a breaking bar to get loose. Those two bolts were the most difficult.

Gotcha. Think I might go and make the purchase of the gear wrenches and just put them in my tool bag. Been wanting them anyways.

 

[wetfootnw]

I got my Mopar half doors back from paint and put together last night! Took about 4 hours to assemble them and another hour to mount and adjust.
They look too new!

 

[AlStew]

Got the LoD sliders used from a member. Got them installed now time to get some more rust off and paint these!!

Loving these so much more than my poison spider boat sides and I haven't even used them yet!

 

[OscarMike2.0]

I got my Mopar half doors back from paint and put together last night! Took about 4 hours to assemble them and another hour to mount and adjust.
They look too new!

View attachment 153041
View attachment 153044

Holy shit that looks good!!! Makes me want half doors for my true blue jk

 

[TeamFaust]

Love the half doors look!

 

[RockyJk]

Got the LoD sliders used from a member. Got them installed now time to get some more rust off and paint these!!

Loving these so much more than my poison spider boat sides and I haven't even used them yet!

If you don't mind me asking why'd you switch to the LõD over the PS?

 

[Panda]

Windshield replaced, completed 8:45 am

New wayalife decal installed 8:55 am

 

[Stegertime]

Windshield replaced, completed 8:45 am View attachment 153172
View attachment 153173
New wayalife decal installed 8:55 am
View attachment 153174

Nice one Rob

 

[AlStew]

If you don't mind me asking why'd you switch to the LõD over the PS?

The poison spyder one never fit really snug against the body and there was a gap. Water and dirt would collect.

Plus all the dirt that would get stuck inside the slider sucked.

I wanted frame mounted sliders too, with a nice step, so these are perfect for what I always wanted!

Next, we got to get some 37's underneath our rigs!!

 

[JLE21]

EVO rear fascia :thumb:

 

[AlStew]

Painted and installed!

They're still a little wet, but I couldn't watch paint dry any longer I'll have to touch up underneath.

 

[RockyJk]

The poison spyder one never fit really snug against the body and there was a gap. Water and dirt would collect.

Plus all the dirt that would get stuck inside the slider sucked.

I wanted frame mounted sliders too, with a nice step, so these are perfect for what I always wanted!

Next, we got to get some 37's underneath our rigs!!

Ah ok yea that dirt n water would probably cause problems later on

View attachment 153225

Painted and installed!

They're still a little wet, but I couldn't watch paint dry any longer I'll have to touch up underneath.

Looks good!

 

[RockyJk]

Finally got the Bow brackets today so I put on the soft top

 

[Spudcannons]

PSC BFH trail stinger, switch-pros, lockers front and rear, ARB compressor.

 

[JRied]

PSC BFH trail stinger, switch-pros, lockers front and rear, ARB compressor.

The front of you jeep looks sick man

 

[Spudcannons]

The front of you jeep looks sick man

Thanks! I just need to figure out where to mount the plate until I get a winch.

 

[shawnrobison77]

Louisiana water is actually full of sand! Pulling shafts to install sleeves, locker, gears, and discovered this pretty little mess. Tubes are full of sand, amazed the seal was good and diff wasn't filled

 

[07JKSahara]

Cut fenders. Huge thanks to panda!
.
.

 

[MotoMatthew]

Panda did mine too!!! What a hero.

 

[wschilawski]

Panda did mine too!!! What a hero. View attachment 153362View attachment 153364

That's my favorite cut-line by far! Panda is the man! Does he ever travel to the Midwest!?