VIDEO - EVO JK SPORT CAGE INSTALL : 2011-17 Jeep JK Wrangler Unlimited

Great video! Thanks for making it. I do like the cage the more I look at it after all this time it's been out. If I could justify the cost I would prob switch from my rockhard over to it just for the slight extra visibility over the dash bar.
 
cozdude said:
Great video! Thanks for making it. I do like the cage the more I look at it after all this time it's been out. If I could justify the cost I would prob switch from my rockhard over to it just for the slight extra visibility over the dash bar.
Click to expand...

You could always sell me yours for cheap then get one!:D
 
JK2DR said:
Do the crossbars on the RH or evo hang low enough to get in the way? If I sit in the passenger seat of my jeep now my head hits the soundbar if the seat is slid back all the way.
Would like to do a cage but not sure if its going to cut back on headroom even more
Click to expand...

You need to talk to SDG here on the forum. I think he's close to 7' tall and got the EVO cage specifically because of his height.
 
Thanks for the video. I recently learned about the new crossbars that replace the factory but also didn't realize there were more plates provided as well. Seems really beefy and its growing on me.

I'm still more of a fan of the tubes of the RH cage compared to the squared off look of the EVO. I'm sure the EVO cage meets the quality of their other products though so it's more of just personal preference. While I don't think I would have an issue with visibility of the RH cage, the wife might and I do like the way the EVO cage provides better visibility as well as almost making it look like it was factory as far as the a pillar goes in the fact that it replaces the factory trim. Well done EVO. [emoji1303]

I'm debating about trying to do a cage soon, now I just have to decide.


Sent from my iPhone using WAYALIFE mobile app
 
LARSONEM said:
Great video. The fact you got the job done with "no colorful language" is simply amazing. LOL.
Click to expand...

:cheesy: I've installed a few cages over the years and in my opinion, this was one of the easiest. As you can see in the video, even the a-pillar supports just went right in and without any fuss.
 
mudmobeeler said:
Thanks for the video. I recently learned about the new crossbars that replace the factory but also didn't realize there were more plates provided as well. Seems really beefy and its growing on me.

I'm still more of a fan of the tubes of the RH cage compared to the squared off look of the EVO. I'm sure the EVO cage meets the quality of their other products though so it's more of just personal preference. While I don't think I would have an issue with visibility of the RH cage, the wife might and I do like the way the EVO cage provides better visibility as well as almost making it look like it was factory as far as the a pillar goes in the fact that it replaces the factory trim. Well done EVO. [emoji1303]

I'm debating about trying to do a cage soon, now I just have to decide.
Click to expand...

The Rock Hard is a good cage and it worked fine for me but the visibility thing was always an issue for Cindy. Even with lower sitting Mastercraft seats in Moby, she still preferred to wheel him over Rubicat and that was before the LS swap. So that it isn't missed, Moby still has a Rock Hard cage but he is an 07.
 
Flat Top said:
Is there any interference to the headlight sensor. I think there was a thread on the forum last month where they needed to move the sensor for it to work properly. Looks like you left it in place, any problems?
Click to expand...
Mine works fine, lights come on a little sooner as it does cast a shadow, but they work like normal unless you get into a shadowy area.
 
Is there any interference with the uconnect mic? Looks like that panel gets replaced but can't really tell. Curious if it needs to be moved.


EDIT: watched it again. Question answered at 6:55. Thanks!

Sent from my iPhone using WAYALIFE mobile app
 
Last edited:
Flat Top said:
Is there any interference to the headlight sensor. I think there was a thread on the forum last month where they needed to move the sensor for it to work properly. Looks like you left it in place, any problems?
Click to expand...

I had to relocate mine... I honestly think I'm the only person who has run into this issue.
 
I keep rewatching the video. Can’t wait till mine comes this week. Install doesn’t look too bad.
 
Does the cage come with the template and instructions? I know it’s online. But I don’t have a computer..
 
You must log in or register to reply here.
Top Bottom