What was done to your rig this week?

I finally installed my tera low transfer case. I like it!!

This was the part I was afraid of. I had been on lifting restrictions until recently. It was way easier than I though it would be.
ImageUploadedByWAYALIFE1394392610.080251.jpg

Empty hole where my t case used to be
ImageUploadedByWAYALIFE1394392633.728601.jpg

Purdy
ImageUploadedByWAYALIFE1394392736.318144.jpg

Install was actually quite simple
ImageUploadedByWAYALIFE1394392778.451869.jpg
ImageUploadedByWAYALIFE1394392820.311380.jpg

Now I need to go get it dirty!!
ImageUploadedByWAYALIFE1394392853.982696.jpg


My ride- 2001 power wheel, 11" plastic tires, upgraded battery, boat sides, custom bumpers, tow hooks, new paint.
 
Finally got the 4" plush ride coils, Metalcloak front control arms, fox shocks, synergy high steer kit installed. With the weather here in Virginia it only took 3 weeks to piece it all together. But it's done so I was able to get it cleaned up today as well and touch up some rust area with rust oleum spray bed liner.
 

Attachments

  • image-4265182584.jpg
    image-4265182584.jpg
    423.5 KB · Views: 402
  • image-2426984575.jpg
    image-2426984575.jpg
    97.6 KB · Views: 376
  • image-4288668259.jpg
    image-4288668259.jpg
    98.3 KB · Views: 388
How did you mount the CB to the metal bracket? I like that look and way of doing it. Was wondering what parts are needed and how it was done so clean looking.

I just used some of the tips that I found from others here to complete my set up. I used 3/4" insulated wire clamps from the electrical aisle at my local big box hardware store (I couldn't locate 1/2" clamps which would have been better) and attached them to the CB mounting bracket with short L brackets. Since the 3/4" clamps are larger than the loop at the center of the windshield, I just wrapped the hoop with electrical tape to make it thicker. This took out any play in the mounting point. To mount the L brackets to the CB mounting bracket, I did have to drill new holes in the bracket as the other holes were spaced too wide and would not work. On the top back of the CB unit, I used velcro to keep the CB from rocking or rattling against the windshield trim over bumps. The coax runs along the driver side windshield trim and into the roll bar padding back to the antenna location. The power cable runs along the passenger side windshield trim and down into the firewall as shown in the Wayalife tech article for installing a CB. The antenna mount is the FireStik NGP mount and it required some light trimming inside the driver side taillight location to make it mount flush. I hope that helps clarify. BTW, ctlazer5 I tried to respond to your PM but your inbox was full.
 
image.jpg

Installed my winch. Pretty easy install but had some problems spooling it. Check out my thread in the General Off-road Tech if you think you could help me out.
 
Today was a maintenance day and install day. First was the install of Rancho 9000 shocks. Cannot wait to see how they feel on the road.
ImageUploadedByWAYALIFE1394409102.234481.jpg
ImageUploadedByWAYALIFE1394409136.669685.jpg

Changed the diff fluid front and rear. Thank you Eddie for the write up on how to do it.

R/
Will
 
Last edited:
Picked up and installed some new electronics. Didn't really want to mount on the dash, but not many options with a full size.

Sent from my SCH-I535 using WAYALIFE mobile app
 

Attachments

  • 1394409827498.jpg
    1394409827498.jpg
    16.6 KB · Views: 325
  • 1394409840343.jpg
    1394409840343.jpg
    53.9 KB · Views: 321
Oil change. Wanted to re torque the wheels spacers and front to back switch the MTs but didn't get that far.....

ImageUploadedByWAYALIFE1394410068.643351.jpg

ImageUploadedByWAYALIFE1394410085.653379.jpg

ImageUploadedByWAYALIFE1394410100.419070.jpg

Maybe next weekend. Busy this week


Sent from my iPad using WAYALIFE mobile app.......
 
No pics, but installed front and rear psc bombshell diff covers. Easy breezy.


Sent from my iPhone using Tapatalk
 
I used the supplied rtv. I figured if psc supplies it, they must get good results using it. :D


Sent from my iPhone using Tapatalk
 
Thanks to Trailready got some trucklites!
ImageUploadedByWAYALIFE1394421347.598569.jpg

Couldn't get the right angle on the front rock lights so I just put a set of platinum burners and also found a way to mount the middle rock lights 👍
ImageUploadedByWAYALIFE1394421455.186864.jpg
ImageUploadedByWAYALIFE1394421472.671657.jpg
 
My weekend of mods came to a close with the following mods done:
Barricade 9500lb Winch installed
Bumper top side mounted Hex Pods installed
Rock lights FINALLY installed and working though I need to reconsider how I'm gonna keep them mounted. Currently just zip tied cause my self tapping screws suck ass -_-

PICS!
My Finished Front Bumper.jpg
All Lights On Inside View.jpg
All Lights On Front Angle.jpg
All Lights On Rear Angle.jpg
Rock Lights.jpg
 
Installed a new bumper and took the chrome Jeep logo off the front grill and installed a new Black logo also, added the JK sticker.ImageUploadedByWAYALIFE1394427164.111368.jpgImageUploadedByWAYALIFE1394427203.078043.jpg
 
Top Bottom