The building of GR8WHITE2.0 aka The Silver Piece

Worked on the jeep some more last night. I got my pinion angle where i think I needs to be. Then i tacked my upper arms together and upper mounts to the axle. To accomplice the full bump Im looking for, I had to cut the floor for clearance of my upper control arms. ImageUploadedByWAYALIFE1482237954.978274.jpgImageUploadedByWAYALIFE1482237973.457745.jpgImageUploadedByWAYALIFE1482237998.842313.jpgImageUploadedByWAYALIFE1482238011.530199.jpgImageUploadedByWAYALIFE1482238038.936827.jpg
 
Keep making steady progress. All 4 amrs are tacked together and all mounts are tacked onto the axle. Put the tire on to start planning the backhalf/cage. ImageUploadedByWAYALIFE1482373469.131084.jpg ImageUploadedByWAYALIFE1482373556.303184.jpgImageUploadedByWAYALIFE1482373566.933627.jpgImageUploadedByWAYALIFE1482373576.713910.jpg
 
Got some more knocked out this morning. Started bending my main piece of frame. (It will sit a little higher and flatter than in the pic) Then I cleaned up and grinded all the factory control arm mounts off. Then made plates that with have a hole cut in them to slide over the tube and weld to the frame. ImageUploadedByWAYALIFE1482435955.100301.jpgImageUploadedByWAYALIFE1482435965.627065.jpgImageUploadedByWAYALIFE1482435977.024642.jpgImageUploadedByWAYALIFE1482435985.127608.jpg
 
My Christmas morning was spent in the shop and got the main rear frame section completely welded into place. Gonna clean up and grind down the extra overhang of the frame plates eventually, ImageUploadedByWAYALIFE1482724721.031733.jpgImageUploadedByWAYALIFE1482724740.895736.jpgImageUploadedByWAYALIFE1482724753.577173.jpgImageUploadedByWAYALIFE1482724761.830104.jpgImageUploadedByWAYALIFE1482724778.495932.jpgImageUploadedByWAYALIFE1482724789.621783.jpgImageUploadedByWAYALIFE1482724804.927160.jpg
 
Got some more knocked out this morning. Started bending my main piece of frame. (It will sit a little higher and flatter than in the pic) Then I cleaned up and grinded all the factory control arm mounts off. Then made plates that with have a hole cut in them to slide over the tube and weld to the frame.

My Christmas morning was spent in the shop and got the main rear frame section completely welded into place. Gonna clean up and grind down the extra overhang of the frame plates eventually,

View attachment 235987

View attachment 235988

View attachment 235992

I'm not seeing how this tube is supported other than the single point (plate caps). Where else did you attach it? I'd think you'd want this point super beefy if it's going to support the cage, etc.

Normally, I've seen square tube used that's slightly smaller than the stock framerails slid inside which gives a huge contact patch for strength.
 
I'm not seeing how this tube is supported other than the single point (plate caps). Where else did you attach it? I'd think you'd want this point super beefy if it's going to support the cage, etc.

Normally, I've seen square tube used that's slightly smaller than the stock framerails slid inside which gives a huge contact patch for strength.

Just wait, you will see how beef it's going to be. The entire cage and everything else is going to be welded to it. U never seen a backhalf tube jeep buggy? It will something look like this ImageUploadedByWAYALIFE1483469436.586103.jpg
 
I can envision what you're working towards, and I wasn't trying to say you're doing it wrong, I just couldn't see where else the tube attached to the chassis. Maybe I'm jumping the gun though.
 
I can envision what you're working towards, and I wasn't trying to say you're doing it wrong, I just couldn't see where else the tube attached to the chassis. Maybe I'm jumping the gun though.
The tube does only attach to the frame there... The roll cage from the A pillar to B pillar is going to be tied into the factory fame in 6 different locations. Then all that is getting tied into the the rear tube frame section making for an incredibly stout and rigid chassis. So the rear back half is not "supporting the cage" its getting tied into the cage that will be supporting it and making it even stronger. Wait until the cage is completely done and you will see where im coming from.
 
Got to work mounting the seats. Made some brackets out of 1/4" that will be directed welded to the main lower tubes of the cage. Still need some more tube run along the floor to mount the front of the seats. ImageUploadedByWAYALIFE1483572266.292698.jpgImageUploadedByWAYALIFE1483572293.654073.jpgImageUploadedByWAYALIFE1483572311.997969.jpgImageUploadedByWAYALIFE1483572322.539405.jpg
 
Top Bottom