Good Bye AEV...Hello EVO!

I have a JE REEL 1350 front budgeted into my Build...

Thanks for the Info!! :thankyou:


Donny
 
Santa came to Boulder City early! Now I just need to find the time to do the install...:thinking:
IMG_2504 (640x427).jpg
 
FoxC said:
Santa came to Boulder City early! Now I just need to find the time to do the install...:thinking:
<img src="http://wayalife.com/attachment.php?attachmentid=9174"/>

Well if your short on time, I can drive down and install it on Knuckles instead. ;)
 
Finally getting to this axle swap:
IMG_2525 (640x427).jpg
IMG_2527 (640x427).jpg
Word to the wise: those damn speed sensors are VERY fragile!!!:grayno: I knew to be careful with them, but wtf...I still managed to brake the passenger side.:doh: Got lucky and found one in stock at a dealer in California. Hopefully it will be here on Monday.
 
Finally getting to this axle swap:
<img src="http://wayalife.com/attachment.php?attachmentid=11231"/>
<img src="http://wayalife.com/attachment.php?attachmentid=11232"/>
Word to the wise: those damn speed sensors are VERY fragile!!!:grayno: I knew to be careful with them, but wtf...I still managed to brake the passenger side.:doh: Got lucky and found one in stock at a dealer in California. Hopefully it will be here on Monday.

Very nice man! I bet that pr44 is heavy as hell. My wife would love to see that outsude our door... she had trouble getting my ps brawler lite inside.
 
FoxC said:
Finally getting to this axle swap:
<img src="http://wayalife.com/attachment.php?attachmentid=11231"/>
<img src="http://wayalife.com/attachment.php?attachmentid=11232"/>
Word to the wise: those damn speed sensors are VERY fragile!!!:grayno: I knew to be careful with them, but wtf...I still managed to brake the passenger side.:doh: Got lucky and found one in stock at a dealer in California. Hopefully it will be here on Monday.

Looks good FoxC!!!

You doing it alone?

Question will the EVO trackbar bracket fit without modification? What about the draglink flip kit install?
 
Looks great man!
How was the ride difference of the King 2.0s vs the AEV 5100's im assumung?

And you already have your old D44 spoken for?
 
Looks good FoxC!!!

You doing it alone?

Question will the EVO trackbar bracket fit without modification? What about the draglink flip kit install?

Yep..doing it alone. Ok a little help from my son, but with 2 floor jacks it hasnt been too difficult.

You need a new raised tracbar bracket for the pr44. I had them weld it on when they built it so the draglink flip and everything just swaps over.
 
Very nice man! I bet that pr44 is heavy as hell. My wife would love to see that outsude our door... she had trouble getting my ps brawler lite inside.
It is heavy. Thats been the most difficult part to the swap. It feels like it's twice has heavy as the d30.:crazyeyes:
Looks great man!
How was the ride difference of the King 2.0s vs the AEV 5100's im assumung?

And you already have your old D44 spoken for?
There really is no comparison between the kings and the bilsteins. waaaaaay better. very happy with that purchase. The pr44 is replacing a d30.
 
Time for an update: got the pr44 finished up. Went ahead and added front upper adjustable CA's to dial everything in a bit more. After adjusting the caster with just LCA's I felt the axle was sitting back in the wheel well a little too much. Finished up the compressor and started the plumbing to the lockers this morning:
IMG_2533 (640x427).jpg
Changed rear gear oil and added a dynatrac rear diff cover.
All clean and ready for fresh fluids:
IMG_2532 (640x427).jpg
a little bling for the rear end!
IMG_2535 (640x427).jpg
 
Top Bottom