Search results

Just wanted to share with everyone that I tried the 2” DP accessories lugs and they were just too short. I ultimately went with the 3” Gorilla lugs (as earlier recommended). Good to roll! Sent from my iPad using WAYALIFE mobile app

I have been looking for a wireless camera setup that I can setup for use with an android or apple tablet. My JK head unit is just the standard non nav unit so I use a tablet mounted on the cage for just about everything, however I can’t seem to find a wireless camera setup that I can connect up...

I recently installed the Rock Hard Sport Cage and have been looking for mounts for my phone, iPad or other devices. Looking at the RAM mounts they have the Large Tough Claw which should fit onto the sport cage bar, but not sure what other components I would need, since it looks like everything...

Hey All, this past weekend we got the axles connected. Looks like I was missing the Parking Brake adapters (called Dynatrac today and they are sending them out) and also instructions for the reroute (Dynatrac e-mailed me the .pdf for it). Those of you who have rerouted the OEM Parking brake...

Hey Folks, I finally received my axle set and will be installing them shortly. We will be doing a garage party to get them installed. Looking for feedback/gotchas from anyone who have already installed them. Is there anything I should be preparing for as part of the installation, and pre-work...

Hey everyone, I pulled the old and worn out OEM seats from my Jeep JK and upgraded with some suspension seats. The new seats do not reuse the OEM seat belt setup, so I am going with a 5 point harness. I resolved the seat belt warning by reconnecting up the seat belt receiver with the connector...

I'll be installing axles with the ARB Air lockers (already installed in the housing), but what else is needed for operation? I have run E lockers on my rigs in the past, simple setup, however I am not sure all of the components that would be needed to operate the Air Lockers. Here is my thought...

Yes, the time is near so I'm shopping for some beadlock rims. A few options come to mind: Method KMC ATX Hutchinson Trail Ready They need to fit on*8 on 6.5 wheel bolt pattern. Any recommendations or wanrings from existing owners?

I'll be installing the Hard Core ProRock 60/60 Axle-Set and since all 4 wheel will also be upgrading from the single piston to the dual piston calipers, should I also upgrade the Master Cylinder? I have read that there was an OEM change in the MC between the 07-11 JK and then from 12+, however I...

Hey folks, I'm wondering what owners who have replaced their factory fender flares have done trimming out the rear fender area (see pics). I was looking to cut it out but wondering what was being used to fill/cover/clean up post cut. Suggestions welcome, TIA.

Hey folks, since pulling off my OEM fender flares and losing the plastic factory inner liners I want to get my inner wheel wells lined (factory paint in there is crap) and I have seen that most offer a color mix as well, which I might go with (white). There are numerous manufactures now...

Yup, I got some nutsertin' to do on the Jeep. Looking for some feedback on the best tool to do the job. I know it's a pain in the ass to do and don't mind spending some good $ on it, since having the right tools for the job makes it easier. Please paste in links or part/model #s please. Thanks!

I am changing out my calipers and I was looking up what the torque setting are for the banjo bolt and for the clipper back to the knuckle. I found this: http://project-jk.com/jeep-jk-write-ups/jeep-jk-wrangler-torque-settings#brakes My question is on the brake caliper itself, there are 2...

I'll be change out my calipers on my JK and I know there are some vehicles that need to be bled out in a certain order. Does anyone know if there is a specific order for the JK as well? The manual does not say and can't find anything on the Interwebs. Thanks in advance!

here is mine

We cut a buddy's PAINTED Fender Flares on his rig. We were a bit skeptical on how it would turn out and if the paint would crack under the saw. Turned out great, no issues at all. If you are planning on cutting your fenders check it out. I also have a full instructional video on my channel on...

Hello fellow Jeep fanatics. I have been contemplating building a Jeep that I can use..well anywhere. I have a JK build that I am leaving modified as is (except for maybe some small changes) and I sold my YJ (regret doing that), so I'll be looking for a new rig to start off with. So, I ask you...

Hello everyone, I am looking for some guidance or suggestions on dealing with a paint issue I am having with my Jeep. The short of it is that "Jeep" service stated that it would not be covered under warranty. I expect my next step is to get an attorney, however I wanted to get feedback from...

Because I like stopping just as much as I like going! After upgrading to 37"s and all of the other additional metal that was added, stopping on 2+ tons on stock brakes is not so much fun. I like having fun and fun is an upgrade! Thanks for the opportunity!

I need to replace my shocks, took a hit on the back shocks on some rocks. I have the Metalcloak Gamechanger 3.5" lift that came with the OME shocks. I was looking at the Fox IFPs and see they have 2 sizes, which run from 1.5" - 3.5" and 4" to 6". So, my question is, do I go with the 1.5" to 3.5"...