Search results

I started using these on my Nissan 350. I would swap between blue and colorless brake fluids after 2 or 3 track days. You can no longer get dyed brake fluid for some BS regulation, eve though it makes it so much easier to know when the old fluid had been flushed. I still have it, but...

Still looks low in the back. Also what would this cost to install and alignment? Offroad Warehouse/4 wheel parts quoted $1200 plus tax & shop fees. Took it for a quick drive around the hood. We have a road with very aggressive speedbumps and I didnt hear any unusual noises or binding...

Eddie, your videos and guides are awesome. The rear lift went on so much faster. On the passenger rear uca frame bolt, I use needle nosed pliers on the flag nut to get the spacing correct. Then lined it up looking through the frame ond uca before feeding the bolt to it. Took a few tries...

Thanks. I was able to pry the mount open and remove the brake line. I hate using a grinder with cutting wheel in close & tight quarters.

Thank you for these guides. Finished the lift using this and the how to for beginners video.

One more question. On the front brake bracket attached to the LCA, instead of zip tieing it the LCA, would drilling out the mount to attach it to the shock be a good idea, or just cut off the bracket? It doesn't look like it would snag anything if left dangling. Thank all for help and laughs.

Outlawed the exhaust or broken truck stance?

Are the fenders the same height. Currently the front is 42 inches, the back is 39.5 so 2.5 inch change... I didnt measure before the front lift.

Front half done. Didn't have time tonight to do the back.

I was more focused on getting the lift on. I may try again and take pictures. But laying on the floor struggling to get these to work, a picture was the last thing on my mind. Could be a generational thing in not needing to document everything in life.

I didnt take any. Hands covered in grit.

So I got the front don't minus the sway bar links. The videos were very helpful. Took me about 9 hours just for the front. It was getting late, so I left the stock track bar on. The steering looked pretty centered. I'll try that another day. I attempted the overland brackets, but trying to...

So today I installed the front of the evo susyspension, but gave up on these brackets. I only attempted the drivers side. I could get the upper installed with the crush tube, but the lower would never line up. I could get it to within an 1/8 inch withe the crush tube. I could force it to...

Thanks. The wrangler suspension is very different than what I had on the solid axle swapped xterra. Realistically, how long did it take you to install that rancho kit? Your video was about 1.5hrs. Just looking to plan out when I can tackle it.

I used an ebay listing from a KY dealership when I bought my 350z. They had 3 Nismo editions listed for model life clearance since the 370s were ariving. A Denver dealer had 2 on lot for about $12k more. Nothing different than the KY dealer other than "market adjustment" so I said I would...

A coworker wanted to see how I wired my new winch. I showed and he asked where the cutoff switch and fuse where after he saw it wired directly to both battery terminals. I said, the cutoff switch is the remote you plug in and the fuse is internal.

I have a Harbor Frieght 5 minutes from me and they had a set with it for $20. It is not included in the 2.5 inch kit. Should I order a rear track bar? And one more question. This parts list shows different part number for left & right springs. They were not labeled L & R and came in the...

Skid plate

Why did you get rid of it? The only think I didnt like was the skid plates. I got it installed before the bumper, then had to take it off to bolt down the winch. But I could only get 4 of the 6 bolts installed. The lower bolt and only 1 of the 2 upper bolts on each side.

Bumper & winch