Search results

Good point. The previous owner must have done that, I upgraded the shaft and added skids later, so didn't even consider that the exhaust had been modified.

I have a feeling this is a bad idea, but I was wondering if it would be possible to put a jack on my exhaust (at the lowest point shown in this photo) to slightly bend it so it's maybe 1/4" to 1/2" higher? It doesn't appear to be supported anywhere near there. Will it give/bend if pressed, or am...

I have a Yellow top Optima, so worse case it should handle being drained better than a standard battery, but I already have a battery tender, so I'm going to use it just because it can't hurt.

My garage is attached. I haven't noticed any evidence of rodents, but I suppose it can't hurt to put a few traps out.

I'll go through the tank of gas within a month of returning.

I'm not going to be around, so not an option.

Yeah, I figured I probably didn't need to worry much about my tires since they're DOT legal radials, not off road bias plys... But since they're pretty new (37" MT Baja Boss AT), that investment is fresh in my mind.

I'm going have to leave my Jeep unused in my garage for about 3 months. What all should I do to prepare it? I was planning on putting Stabil in the fuel and running it through the system for a few miles, putting it on a battery tender, and probably jacking it off the ground just to make sure I...

I have a good amount of surface rust forming on my axle and some suspension components. I've done a bit a reading but am still not really sure what the best course of action is. I'm going to start by cleaning the surface a bit with flapper disk where possible, wipe it down and spray with...

I would still like to be able to control the light with the switch, even when the ignition isn't on. I was also concerned that adding this light to the brake light circuit might overload it.

I have small LED light on my spare, it's connected to an S-Pod that was installed by the previous owner. I was wondering if it would be possible to wire it up to function as a reverse/backup light as well? So it would come on when I hit the switch on the S-Pod or when I put my Jeep (manual, if...

That was kind of my thought, That was basically my thought, just annoying to have any damage before they're even on the Jeep.

I bought a set of tires through a local store part of a chain and mounted them on beadlocks. I didn't remember until I had a couple mounted that they're asymmetrical and had one backwards. The shop said they'd remove it for me (I had already set the bead). I just noticed a chunk (probably only...

True. Unfortunately I don't get to wheel as much as I'd like as I have three little kids and the closest place is about 3 hours away, so balancing drivability around town is important (trying to keep from hurting braking and acceleration performance too much). I'm also going to be on my stock...

I've been considering beadlocks and was surprised to see such a weight difference between these two: Machete Crawl KM22979050538N: ~45 lbs Grenade Crawl KM23579050538N: ~35 lbs Overall the appear very similar, and even have the same load rating, I was surprised to see that the Machete is nearly...

37s and axle regear!

I have a 2015 JKUR with the Mopar Stage 3 lift kit and have been trying to improve my steering. After installing new ball joints, tie rod and drag link I got an alignment and found my caster was only 3.2 degrees. My lift kit doesn't have adjustable control arms, so I was considering replacing my...

I have a 2015 JKUR with the 3" MOPAR lift on 35s. It currently has about 35,000 miles, I've only put about 4,000 miles on it and the previous owner did most of the modifications shortly after buying it new. Since I've had it I've noticed a lot more play in the steering more recently. The...

I have a manual 2015 JKUR with the 3" Mopar lift, 295/70r18 (basically skinnier 35s) tires, stock 4.10 axles and I feel like I really have baby the clutch when starting from a stop compared to other stick shift vehicles I've owned. From the charts and posts I've seen, it sounds like 4.56 is...