Search results

Before I could even get the whole question out they said I'm fine on the concrete... To your points on safety I even pushed a little bit and asked if it would be better to tell the concrete in that area and they quickly said; "No, as long as the concrete in the area isn't cracked it's more than...

Thanks ^^^ I haven't seen many 57s in white. I like it :thumb:

One of my hesitations is that while I have 6" of concrete, it doesn't have metal in it. The requirements are for 4" with metal. I will need to call them to see if it is okay or not.

I am in the market for a 2-Post lift and wondered if any other of you have on in your shop? What you think of it? and if you would buy it again? Did you install it or have it installed? If you did it how difficult was it? I'm thinking about this one ->...

So I'm laying all my parts out an preparing myself mentally for my upcoming lift install and have a few questions that isn't covered in the directions. I searched here too, but still didn't come up with an answer so here they are: I ordered extended brake lines, but the wheel speed sensors run...

Getting ready to order drive-shafts in prep for the lift. I've been wavering on 1310 or 1350 joints. I will be running 35s (Likely Goodyear MT/R-K) I have also kicked the idea around of a smaller 37 like the BGF KM2 but am avoiding this as I don't really want to re-gear (yet) and I feel the...

Just what the title says... I went to order some front shock axle relocation mounts today online and their security certificate has expired. Since I didn't want to enter my information on a non-HTTPS site I tried to call... Their number just rings busy. I also noticed there haven't been any...

37x13.50 R17LT

I check my nuts all the time.... It's true, the wife even complains about it ;) So then I check her headlights :D

Does anyone else have any issues with the revers lockout on their Manual Tranny? While most of the time I drive like an old man, there have been a few times I jumped into it taking off. Usually when I do this I only go nuts through first and second, and maybe a touch of third. Since I'm already...

I am just a month or two from finally ordering my lift and I’m looking for some feedback from this great WAYALIFE knowledge ball. I have a 13’ JKUR. I am going to run 35s. (Never any intention of 37s) I have PSC narrow tube fenders too. I plan on doing the drive-shafts at the same time I lift...

I have tried several forum and general internet searches but never found the answer.... Does anyone know what the stock JK Alternator puts out at idle? If there is a difference in years mine is a 13' I signed up for a parade in December where I need to run a whole bunch of lights (Christmas...

Check out what I found! What do you think? http://www.eastwood.com/internal-frame-coating-w-spray-nozzle-qt.html

I agree with a good primer and/or sealer being sufficient, my trouble is getting it where it needs to be. Here is a picture of the area of concern. How do I get coverage behind the mounting plate? Sorry for it being a little outta focus. Thje camera on my phone is jacked.

So, Brown Santa dropped off our new PSC Brawler Lite front bumper yesterday and the test fit went perfectly. Now it’s time to finish it. I ordered it unfinished because I planned to do some slight modifications for a license plate mount. After looking at the backside of the bumper, I am worried...

I am in need of a stock JK passenger side headlight globe (assembly). Long-story-short. I installed Oracle halos and some LEDs failed. They replaced the ring, but I don't want to re-open my globe a second time. I would rather just start over on a new globe. I am a bit picky so I am only...

No lift... (well not really). I have a TF leveling kit. I used a 1/2" spacer instead of the second 1" spacer up front because I didn't have that much rake at the time. It has 1.5" front and 1" rear spacers. The lift is next on the list. The PSC flares make it look like there is more lift. This...

I've got some JK stuff that I want to get out of my shop... All Free but you must get it by Tuesday or it will be headed for a landfill. I am also listing them on some other forums I frequent first-come-first-serve *Stock Rear Bumper, (Minor damage on passenger lower corner - scratches from...

Hello all, I just wanted to promote my club's Jeep Jam that is coming up soon. Last year there was over 500 Jeeps and we hope for more this year. The obstacle course and trail rides are tailored for stock or lightly modified Jeeps. The property where it is held was new to us in 12' so we are...

I posted some of this in another thread DIY thread and originally linked to another forum where I posted the write-up. I got some feedback that some would like it here, so here you go... BTW I have also been made aware that some may not be able to see the pictures from the site I use to post...