Search results

My Juggy is set up using the winch on the front as a suck down. Nothing wrong with doing that but unless you front end is stretched out there cable is pulled way back and Ive seen cables severed from being smashed between rocks and the bumper like that. I plan to put it right behind the gate...

Last night I started to mess with the bender and got a tierod build. Its got 20* bends on either side and now I realized that I should of put more bend in it because I ended up a bit long and barely getting into the diff cover. Im hoping I can just stick it back in the bender and get a bit more...

Well popped my cherry today and went for a ride in the Juggy.

Just realized I also had a picture of trail 39 near the end.

Figured Id throw up some of the pictures that were taken of me on rattle rock. Sadly I didnt get anything else of anyone.

Together now just time to get the front driveshaft in and this turd up on the trailer.

Well couple weeks ago on what I call my Juggy a 79 CJ7 snapped the old heims. They were tiny.

Any bets if this is on the juggy by thursday night?

Not very knowledgeable on 4BTs but I know if its anything like a 6BT they are known for leaking. However, I do agree if its a brand new motor it shouldnt be leaking that quick.

Well today I got the struts figured out. Didnt call or anything just made sure all air was out and started over. Here is where I have it sitting now. Im going to roll with this height for now. Im guessing after struts break in it will settle and ill have to reset. Of course I also had to...

Today I ended up trying to charge the ORIs but was having problems getting it to take any pressure. I plan to call ORI tomorrow and see what it is Im doing wrong. The lower cambers seemed to take some because after I was able to bleed some pressure off. When I tried to do the top it wouldnt take...

I couldnt stand it so I decided to put the front end back together. I ended up sticking the factory tierod on just to make it a bit easier to move around for now. I cant wait to flex this thing out tomorrow and see how it does.

Well I feel like I have accomplished too much today lol. Day starts by going wheeling and breaking a lower control arm on the juggy and being home even before lunch time. After I unloaded it when I got home I put the JK back up on the lift and started to pull the front end back out of it...

Today I decided to go ahead and put my Mastercraft Rubicon seats in since the Jeep was already on the ground and sitting low. They went together very easy and I was surprised to how well the fitment is. I will say they sit a bit lower then factory seats do and in my case I consider that a good...

Im sure this is hard to believe but finish mounting up the last strut. Here is some of the pictures of cutting it up and finally welded to the frame. The towers ended up within .5 degrees of each other so im happy with that. Lastly here are pictures of full bump and full droop. Also Im...

I had my 7/8 Ruff Stuff heims with 3/4 milsalinment spacers show up the other day for the tierod and draglink I gotta build. I also had my Teraflex big master cylinder show up. It may be at the next pre run if you will be there. Thanks guys

Last night turned out to be a great night when we got the driver side front tower all tacked in. It looks like everything is going to be good and I wont have to mess with it any further. Next on to the other side and the Jeep will be roller. It will be odd seeing the Jeep on the ground. I...

Finally started to mess with the ORIs on the front of the jeep. Had to clean up both sides of the frame and take a bit more of the factory coil buckets off the top of the frame. Started cutting on the one mount and I think I have it fitting pretty close to how it should on the frame. Looks like...

Been making up for all that wheeling time I have missed, but I plan to get back at it here shortly. Today I did do a little even though it wasnt much. Ended up cutting more of the Cs off so I have clearance for the ORIs. It looks like I have plenty of room now and shouldnt have to mess with it...

Havent worked on the JK in awhile. I need to stop having fun and get back to it. Today my MasterCraft Rubicon seats showed up. I got 2 for now. After seeing how they go may end up putting 4 race seats in it or moving the fronts to the back. I got the driver seat with the CamelBack, but the...