Recent content by Hendu3270

  1. Hendu3270

    Testing airbag circuits?

    Thank you coz
  2. Hendu3270

    Testing airbag circuits?

    Airbag is sitting in the garage. I run it into a wall I'm eating the steering wheel. Lol
  3. Hendu3270

    Testing airbag circuits?

    Code B1B02 Driver Airbag squib 1 circuit open. I removed the airbag and was wanting to see if I was able to figure out which connector from steering column is for squib 1. Yellow or black. Anyone know where this info is and also is there a way to test these connectors? I'm not an electrical guy...
  4. Hendu3270

    Wheel Speed Sensor (dealer or after market?)

    Just as title states. I know O2 sensors need to be OEM as after market won't work. What about wheel speed sensors? Autozone sensors work fine? What's the general consensus? Thanks guys!
  5. Hendu3270

    3.8 internal (engine/intake) coolant level

    Thanks for the input guys. This helps confirm what think happened.
  6. Hendu3270

    3.8 internal (engine/intake) coolant level

    Under normal conditions...thermostat opens and allows the interchange of water. When it closes...where is the coolant level? Or is there no air on the intake side of the thermostat? I'm trying to determine if the water channels in the intake manifold would be full of water when removed or if...
  7. Hendu3270

    What could still be dripping??

    Stirred it after work. Black on top and that brown is underneath. Once I stirred it a little it looked just like the photo above.
  8. Hendu3270

    What could still be dripping??

    One thing I did do is, on that day we drained the brownish oil, I took a jar and scooped up some of that brown oil and set the jar on my work bench with a tupperware container on top of it to see if it would settle out so I could see if a layer of coolant formed on top (or possibly fuel). When I...
  9. Hendu3270

    What could still be dripping??

    No, I haven't. If it was coolant though, it should be on top I'd think.
  10. Hendu3270

    What could still be dripping??

    I didn't actually drain any coolant, no. We disconnected the radiator hose from the thermostat housing and there wasn't much in the hose at the time and I didn't think about if there may have been coolant in any of the passages in intake manifold. At any given time, is the water passages in the...
  11. Hendu3270

    What could still be dripping??

    The drain pan had nothing in it when we started. The oil drained out of the oil pan that color. Engine ran really good when we took it for a quick test drive after doing the misc work stated above. Then it sat for one week before we got back under it and dealt with the broken pan bolt. I can't...
  12. Hendu3270

    What could still be dripping??

    Thanks for the responses guys. I think I'll bolt the oil pan back up, pour in fresh oil and just check how the oil looks each day. This is a pic of the oil the day I drained it (5 miles on it) just to see what I was seeing.
  13. Hendu3270

    What could still be dripping??

    Recent repairs........ Valve cover gaskets, oil pan gasket (riser), intake manifold gasket and all injectors cleaned and new O-rings replaced while it was apart. Broke an oil pan bolt and was planning to just keep rolling after I completed everything else unless it leaked. It leaked. Extracted...
  14. Hendu3270

    Quick tie-rod and drag link question...

    Started experiencing DW a few weeks ago. There is no slack in any tie-rod ends or ends of the drag link, Trac bar is solid (or at least I can't budge when I'm under the vehicle). Wheel bearing have no play that I'm able to tell and prying up under the wheels shows zero play in the ball joints...
Top Bottom