Home
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Install the app
Install
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
DaBank's latest activity
DaBank
replied to the thread
HOW TO: Properly Adjust 8 Adjustible Contol Arms
.
@wayoflife I have long arms.
Mar 11, 2024
DaBank
replied to the thread
HOW TO: Properly Adjust 8 Adjustible Contol Arms
.
@wayoflife Would this apply to a 5" lift also?
Mar 10, 2024
DaBank
replied to the thread
HOW TO: Properly Adjust 8 Adjustible Contol Arms
.
Great write up!! Thank you
Mar 10, 2024
DaBank
replied to the thread
Alignment specs for 5" long arm kit?
.
I adjusted the front upper control arms 2 turns shorter and that put my angle finder at 91.6° and 91.5°. Since I adjusted the caster do...
Mar 7, 2024
DaBank
replied to the thread
Alignment specs for 5" long arm kit?
.
I don't know what Chat gpt is but yes I know I am asking about numbers that are close. Just want to make sure I do it right. I been...
Mar 7, 2024
DaBank
replied to the thread
Alignment specs for 5" long arm kit?
.
I have 4.88 gears and I am only taking it back because they said they would check it ONCE for free after I make adjustments since they...
Mar 7, 2024
DaBank
replied to the thread
Alignment specs for 5" long arm kit?
.
So I am at 3.8° based on my level readings on the axle and my floor. The Alignment print out shows 3.3° so my reading is .5 more...
Mar 6, 2024
DaBank
replied to the thread
Alignment specs for 5" long arm kit?
.
I have not adjusted anything yet. On the front I was checking my Caster angle using the front axle flat bases. The level is saying...
Mar 6, 2024
DaBank
reacted to
jeeeep's post
in the thread
Alignment specs for 5" long arm kit?
with
Like
.
do a youtube search for thrust angle, rear axle alignment. if the rear brackets are an 1/8 inch off, that's a starting point but you'll...
Mar 4, 2024
DaBank
reacted to
dchew's post
in the thread
Alignment specs for 5" long arm kit?
with
Like
.
It's best to just measure the starting arm length and turn until you get the added length you want using that 1/2" figure. If you can...
Mar 4, 2024
DaBank
replied to the thread
Alignment specs for 5" long arm kit?
.
I bought the Jeep new in 2018 and had it lifted at 200 miles and now it has 50k miles. Jeep just installed a complete new front 44...
Mar 4, 2024
DaBank
replied to the thread
Alignment specs for 5" long arm kit?
.
I have used the DIY thread in the pass for toe, steering wheel. My thrust angle has been off since the Jeep has been lifted but now a...
Mar 3, 2024
DaBank
replied to the thread
Alignment specs for 5" long arm kit?
.
Dave thank you!! The axles are oringal. I have a 2017 Jeep JKU Rubicon Recon. I just checked my wheels and they are 17x9 with 4.53 back...
Mar 3, 2024
DaBank
reacted to
dchew's post
in the thread
Alignment specs for 5" long arm kit?
with
Like
.
Sorry probably should not divide the axle by 2. I’m not sure how Thrust Angle is defined. Edit: If I understand the definition...
Mar 3, 2024
DaBank
reacted to
dchew's post
in the thread
Alignment specs for 5" long arm kit?
with
Like
.
Pretty close. I'm not sure what the track is of your setup. Depends on your backspacing, axle length, spacers, etc. I think stock is...
Mar 3, 2024
Home
Members
Top
Bottom